Ritron OUTPOST Series Technické informace stáhnout pdf (Strana 18)

OUTPOST Wireless Callbox GateGuard™ Specific Applications

XT G

ATE

UARD

™ I

NSTALLATION

NSTRUCTIONS

.......................

The XT OUTPOST™ can be mounted to virtually any

surface with four (4) ¼” panhead screws. Choose a

type of screw thread and screw length which will hold

firmly in the surface to which the unit will be mounted.

MOUNTING the XT OUTPOST™: ( Refer to FIG-4)

1. Remove the front faceplate from the XT Callbox.

The faceplate is secured to the case with 4 van-

dal-resistant buttonhead, Torx screws. Use the T-

25 Torx bit included with the radio to remove

these screws.

2. Remove the “Mounting Bracket” kit secured to the

inside of the XT Callbox case.

3. Due to the wide variety of installation possibilities.

RITRON does not provide the cables or hardware

required to bring external connections into the XT

Callbox. When selecting your cable hardware be

sure it will adequately seal the cable to the case.

Carefully study the internal construction of the XT

Callbox and determine the location on the outside

case where the external supply and GateGuard™

hook-up will be brought in. Consider clearance

with your desired hardware.

4. Remove the 4 flathead screws securing the inter-

nal mounting plate and remove entire internal

case assembly. The front faceplate will be at-

tached to the internal case assembly, handle with

care.

5. Carefully drill the hole in the XT Callbox case re-

quired for your external hook-up cable installation.

6. Install the 4 mounting brackets to the back of the

XT Callbox case shown in FIG-2 on page 5. The

mounting brackets can be installed vertically, as

shown, or horizontally.

7. CONNECTING the GATEGUARD™ to an

EXTERNAL DEVICE

Thread your external hookup cable from the ex-

ternal device you wish to control through the hole

with approximately 6 inches of cable inside the

case. Your external cable will be connected to the

XT Callbox 6-conductor interface cable with

wirenuts, dress your external wires accordingly

(Refer to Table 6). With your selected hardware,

secure and seal

the conduit to ensure moisture

and vandal resistant functions to the XT Callbox

case.

Consult the manufacturer of the external device you are

attempting to control for the recommended wire gauge.

Confirm that your application will NOT exceed the maxi-

mum rating of the on-board relay of 120 VAC @ 1 amp.

Make sure all power to the equipment is turned OFF or

disconnected.

CAUTION: The interface cable and wirenuts

should be positioned on the right

side of the

case opposite the antenna (See FIG-4 on page

17)

8. Position the XT Callbox case in the chosen instal-

lation location and secure it in place with four

screws through the mounting brackets.

9. If programming is required, loosen the (4) captive

screws in the front corners of the internal Callbox

case and separate the case front from the case

back. These screws are captive to the housing; to

prevent damaging them, DO NOT remove the

screws from the housing.

10. Program the radio, if required. Refer to the pro

gramming section of this manual for details. To

program the radio you must first apply +12VDC

external power, or alkaline batteries.

11. If rechargeable NiCd batteries are used for bat-

tery backup the “Charge Jumper” must be placed

into the “charge” position as shown.

! ! CAUTION ! !

If rechargeable batteries are NOT used for battery

backup, be sure the “Charge Jumper” is NOT in

the “charge position. Charging alkaline batteries

will damage the cells and reduce battery life!

Char

FIG-3: Charge Jumper in Charge Position

12. Fasten the internal case front to the case back with

the four (4) captive screws. Do not over-tighten the

plastic screws to prevent damage.

13. Secure the internal case assembly to the XT Call-

box with the 4 flathead screws through the inter-

nal mounting plate. Refer to FIG-4 for correct ori-

entation and location of the antenna and cables.

The front faceplate is attached to the internal case

assembly, handle with care.

14. Re-fasten the front faceplate to the radio with the

4 buttonhead Torx screws.

16 Have questions? Call 800-USA-1-USA (800-872-1872) or visit our website at www.ritron.com

1 2 ... 13 14 15 16 17 18 19 20 21 22

Komentáře k této Příručce

Žádné komentáře

Ritron OUTPOST Series Technické informace Strana 18

Komentáře k této Příručce

Související produkty a manuály pro Obousměrná rádia Ritron OUTPOST Series