RADIO PROGRAMMING
Have questions? Call
800-USA-1-USA
(800-872-1872) or visit our website at www.ritron.com 13
TABLE 2: INTERFERENCE ELIMINATOR
PROGRAMMABLE QC TONE
Code Hz Code Hz Code Hz
01 67.0 18 123.0 35 225.7
02 71.9 19 127.3 36 233.6
03 74.4 20 131.8 37 241.8
04 77.0 21 136.5 38 250.3
05 79.7 22 141.3 39 69.4
06 82.5 23 146.2 40 159.8
07 85.4 24 151.4 41 165.5
08 88.5 25 156.7 42 171.3
09 91.5 26 162.2 43 177.3
10 94.8 27 167.9 44 No Tone
11 97.4 28 173.8 45 183.5
12 100.0 29 179.9 46 189.9
13 103.5 30 186.2 47 196.6
14 107.2 31 192.8 48 199.5
15 110.9 32 203.5 49 206.5
16 114.8 33 210.7 50 229.1
17 118.8 34 218.1 51 254.1
00 Delete
TABLE 3: DIGITAL INTERFERENCE
ELIMINATOR PROGRAMMABLE DQC TONE
CODE NUMBERS
023 074 165 261 356 462 631
025 114 172 263 364 464 632
026 115 174 265 365 465 645
031 116 205 266 371 466 654
032 122 212 271 411 503 662
036 125 223 274 412 506 664
043 131 225 306 413 516 703
047 132 226 311 423 523 712
051 134 243 315 431 532 723
053 143 244 325 432 546 731
054 145 245 331 445 565 732
065 152 246 332 446 606 734
071 155 251 343 452 612 743
072 156 252 346 454 624 754
073 162 255 351 455 627
HOW TO DELETE A CHANNEL
1. Follow the instructions in FIG-6 on page
10 to place the radio in the Program /
Readout Mode.
2. Using the CHANNEL
button and the
LED display on the front of the radio,
select the channel to be deleted
.
3. Enter 4-digit code “0000” as described in
the “How to Field Program Frequency &
Tone Codes” section on page 11.
4. When all four digits are programmed,
press and release the On / Volume Up
to SAVE
your programming entry. The
LED display will briefly show the channel
number you have just deleted and the
radio will sound a triple beep to indicate
that channel deletion was successful.
5. To delete another channel, repeat steps
2 through 4.
6. Turn the radio OFF and then ON
again—the radio is now ready to use.
7. The remaining channels are in the same
sequence and will retain their same
channel number. The Channel Selector
will skip over the deleted channel
numbers.
NOTE: If all channels are deleted the radio
will not operate, instead it will turn
on in Field Program mode to allow
entry of a valid frequency and tone
code.
HOW TO FIELD PROGRAM RADIO OPTIONS
1. Follow the instructions in FIG-6 on page
10 to place the radio in the Program /
Readout Mode.
2. Using the PTT (push-to-talk) button and
the LED display, enter the single digit
code from Table 4 below for the option
to be programmed.
3. Pause—the display will change and
show a hyphen, you will also hear a
short low tone.
4. Press and release the On / Volume Up
to SAVE
your programming entry. The
radio will sound a triple beep to indicate
that programming was successful.
5. Turn the radio OFF and then ON
again—the radio is now ready to use.
TABLE 4: Radio Option Codes
Option Code
Turn Channel Scan ON 1
Turn Channel Scan OFF 2
Turn Weather Channel ON 3
Turn Weather Channel OFF 4
Turn Weather Alert
ON 5
Turn Weather Alert OFF 6
Turn Speaker Beep ON 7
Turn Speaker Beep OFF 8
(21 stránky)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce